Link zur deutschen Version: Gut erhalten – und künftig länger genutzt
A research initiative for the structures of the Swiss national road network
A bridge stock in good condition
The Swiss national road network comprises more than 16,000 structures – bridges, retaining walls and galleries – with a reprocurement value of about 47 billion Swiss francs, more than a third of the entire network value. Most of them are built of reinforced and prestressed concrete and are essential to the safe operation of the network.

According to the condition report of the national roads, more than 90 per cent of these structures are in good or acceptable condition, and none are in an alarming condition. Compared to countries with assets of similar age and exposition, this is a remarkable finding, and it is no coincidence. It is the result of systematic periodic condition surveys, a consistently maintained structures database, and a maintenance strategy that prioritises interventions before damage affects structural or traffic safety. The Federal Roads Office FEDRO has run this asset management reliably for years.

These condition ratings are based on periodic, primarily visual surveys. For steering maintenance, that is the appropriate measure – but it says little about the effective structural safety of an individual structure. And it is precisely that question which arises as soon as an extension of the service life is considered. Over the next two decades, it will rise for a large part of the stock.
Why the task is shifting
About two thirds of the bridges in the national road network were built before 1980; their mean age is around 52 years. A large share of the stock will therefore reach its design service life within the next three decades. Because these structures were built in similar periods, many corresponding decisions will arrive in a short period of time.

There is a second point. A structure without visible damage does not automatically meet today’s structural safety requirements, even if it was correctly designed to the codes of its time. And civil engineering is strongly affected by the shortage of skilled professionals: the Swiss State Secretariat for Economic Affairs reports an unmet demand for specialists in the engineering professions, a far-below-average unemployment rate, and an above-average workload per full-time equivalent. The number of engineers able to carry out assessments of existing structures competently is not growing at the rate at which assessments are falling due. On the contrary, many experienced structural engineers are retiring in the next few years.
The task is thus shifting – from preserving today’s condition to the question of how a well-maintained stock can be operated reliably beyond its originally intended service life.
The leverage lies in the assessment
The assessment of structural safety is decisive to answering this question, and such an assessment can err in two directions. If the load-bearing capacity is underestimated, interventions would follow that would not have been necessary, resulting in costs, greenhouse gas emissions, resource consumption, and traffic disruption. If it is overestimated, unacceptable risks arise. Only a reliable assessment makes it possible to limit interventions to the minimum necessary without compromising safety.

There is a relevant knowledge gap here. The mechanical models developed at ETH Zurich – the Tension Chord Model, the Cracked Membrane Model, and their extensions – describe the behaviour of reinforced and prestressed concrete in a mechanically consistent manner, require few, generally known material parameters, and largely avoid empirical calibration factors. They were, however, developed for undamaged structures. For locally damaged members, for instance, those resulting from chloride-induced corrosion, sufficiently validated models are largely lacking. In assessment practice, this uncertainty is therefore covered conservatively.
The unused reserve capacities cannot be reliably quantified today; they depend on the structural system, on the damage pattern and on the deformation state.
Four thematic areas
Quantifying these reserve capacities – on exemplary real structures and with experimental validation – is precisely the subject of our new joint initiative with ASTRA on the «Low-intervention, safe service life extension of engineering structures». Corresponding case studies will be presented in future posts on this blog.

The initiative is organised in four thematic areas.
Material models. The existing mechanical models are extended to account for local damage and validated step by step – from individual corrosion damage through crack element and element tests to large-scale member tests. Topics include corroded bonded prestressing tendons, load-carrying reserves due to compressive membrane action, and the effect of reinforcement acting in a parallel system.
Numerical methods. The models are implemented in nonlinear finite element tools. A best-practice guideline for structural assessment using NLFEA is being prepared, deliberately formulated as software-agnostic so that it can serve to verify various programs. Two prototypes complement this work: an AI-supported assessment tool for typical bridge types on overweight transport routes, and a post-processing tool for discontinuity regions in 2D and 3D. Both are conceived as decision support; they are intended to indicate when an object-specific calculated assessment is required, and do not replace it.
Monitoring. The work examines which measurement parameters and associated techniques enable local damage to be reliably detected and quantified – from the non-destructive assessment of the corrosion state to how measurement data can be fed back into a structural model. This is a precondition for digital twins in concrete construction to become more than an academic interest.
Education and continuing education. The methods developed are integrated into the MSc programme in Civil Engineering at D-BAUG, ETH Zurich. For practising engineers, a CAS ETH in the assessment and preservation of bridges and other structures is being established.

Alignment with FEDRO’s objectives
The initiative aligns with FEDRO’s strategic objectives for the period 2024–2030, particularly with two of them.
Optimised maintenance, which sustainably secures the condition and the value of the national road network (Objective OBJ Q2), presupposes that the remaining load-carrying capacity of a structure is known with confidence. Extending the service life is viable only when structural safety can be verified; otherwise, the conservative alternative remains strengthening or replacement. The initiative provides the basis for that verification.
Reducing the environmental impact of operations and maintenance (Objective OBJ D1) follows directly. Strengthening and replacement cause greenhouse gas emissions and consume resources; every intervention that a careful assessment renders unnecessary or reduces in scope acts directly on that balance – and, at the same time, on the availability of the network during construction.
The content of the initiative builds on priorities that FEDRO has itself set for its departmental research programme 2025–2028: tools for monitoring and asset management, including the modelling of locally damaged primary structural components, the identification of reserve load-bearing capacities where resistance models are conservative and advanced non-destructive techniques for assessing members that are difficult to access. It builds on ongoing and completed individual FEDRO research projects – among them work on retaining walls with local reinforcement corrosion, on the interaction between corrosion and structural behaviour, and on the fatigue of bridge deck slabs – and integrates their results over a longer timeframe.
Timeframe and organisation
The project is scheduled to run for eight years and was launched in the third quarter of 2025. It is organised in two overlapping phases. Phase 1 runs until 2031 and develops the fundamentals in material modelling, numerical methods and condition assessment. Phase 2 is planned for 2028 to 2033 and integrates these fundamentals into service life analyses, the transfer to fatigue damage, and their consolidation in continuing education. The overlap is intentional: service life analyses require robust material models, and setting up a continuing education programme at ETH Zurich requires preliminary work if it is to build on established content.
The individual modules are carried out by doctoral students and postdoctoral researchers of the Chair of Concrete Structures and Bridge Design, in several modules jointly with other chairs at ETH Zurich. Coordination with FEDRO is ensured by a steering committee and thematic advisory commissions that accompany the work in technical and scheduling terms.
What will be publicly available
The outcomes of the initiative shall be implemented promptly, particularly in practice. The doctoral theses and the final summary reports will be freely accessible through the ETH Research Collection; the test data will be published in open data repositories. The algorithms and material models developed will be released as open source in the {StrucEng} Library, accompanied by a wiki containing application instructions, guidance on model limitations and step-by-step examples. In addition, it should be noted that the scientific knowledge gained will be incorporated into the Federal Roads Office’s existing and future new standards.
The individual modules will be presented here on the blog, each by the researchers working on them, and with the case studies against which the methods can be measured.
Walter Kaufmann and Karel Thoma